Kra eu fiz isso ai, estou conseguindo receber ligações no pap2t, mas não consigo efetuar ligaçao, quando tiro fora do gancho fica mudo por um tempo, depois começa dar aquele sinal de ocupado, o que sera que estou fazendo de errado ?
Versão Imprimível
Olha está em ingles, já usei isso a um tempo e deu certo:
So on the 3102, Voice | PSTN Line tab, you want the following settings as a starting point:
Line Enable: yes
Proxy and Registration
Proxy: IP.address.of.PAP2T:5060 (e.g. 10.10.10.1:5060)
Use Outbound Proxy: no
Register: no
Make Call Without Reg: yes
Ans Call Without Reg: yes
Subscriber Information
User ID: PABX (doesn't really matter what it's called)
Dial Plans
Dial Plan 1: (S0<:21>) (the number in the <>'s needs to match the user ID on the PAP2T)
VoIP-To-PSTN Gateway Setup
VoIP-To-PSTN Gateway Enable: yes
VoIP Caller Auth Method: none
One Stage Dialing: yes
VoIP Caller Default DP: none
PSTN-To-VoIP Gateway Setup
PSTN-To-VoIP Gateway Enable: yes
PSTN Caller Auth Method: none
PSTN Ring Thru Line 1: no
PSTN CID For VoIP CID: yes
PSTN Caller Default DP: 1
FXO Timer Values (sec)
PSTN Answer Delay: 0
PSTN Ring Thru Delay: 3
PSTN Ring Timeout: 4
PSTN Hook Flash Len: .1
PSTN Disconnect Detection
Detect Disconnect Tone: yes
Disconnect Tone: 425@-30,425@-30;1(.375/.375/1+2) (this is the Australian PSTN disconnect tone – if your PABX sends a different tone, you will have to change this, otherwise the 3102 wont detect when the line has been hung up.)
International Control
FXO Port Impedance: 220+820||120nF
On-Hook Speed: 26ms (Australia)
And on the PAP2T Voice | Line 1 tab:
Line Enable: yes
Proxy and Registration
Proxy: IP.address.of.3102:5061 (e.g. 10.10.10.2:5061)
Use Outbound Proxy: no
Register: no
Make Call Without Reg: yes
Ans Call Without Reg: yes
Subscriber Information
User ID: 21 (doesn't really matter what it is – but it has to match the number in the dialplan on the 3102)
Dial Plan
Dial Plan: (x.) (you can get very fancy with dial plans, but that should get you started)
consegui não, com este metodo... consegui apenas com outro metodo apenas receber ligaçao, se eu tiro pra fazer uma ligaçao da sinal de ocupado.
Amigos; solucionei meu problema configurando a identificação de tons.
O equipamento para ligar tem que detectar o tom na frequência e intervalos corretos; senão ele entende que não tem tom de discar.
Não sei exatamente como faz isso, foi um amigo craque em Asterix que fez isso.
Agora só uso o Vono e a Intervia; tem que ter muita dedicação e paciência para fazer estes acertos.
A Linksys deveria disponibilizar uma documentação mais adequada, ou mesmo um software de suporte a configuração.
Não tem sites que identificam músicas?
Pois é a CISCO - Linksys deveria ter um meio de através de um microfone identificar este tom e codificar na linha de comando necessária.
Um frequencímetro e um cronometro e um saco de paciência também pode ser uma solução.
Ou contrate um cara bom para fazer um mini asterisk com um PC velhinho + linux [pode até fazer um QOS para preservar qualidade do VoIP] (depois de funcionar não precisa monitor, teclado e mouse) e mandar ver.
Atualmente uso só linhas VONO e INTERVIA; mas seria muito interessante todos postarem suas experiências, positivas ou não, para termos uma Base de Conhecimento.
na realidade, não vou usar planos voip, quero apenas usar uma linha analógica plugada no spa 3102, para enviar para uma fazenda que não chega telefone via rede interna wireless.