Está certo marcação e rotas ?

Tenho duvidas da marcação e rotas se estão corretas vejo que um link sai muita coisa e outro sai pouca:

/ip firewall mangle
add action=accept chain=prerouting comment="Fora Load Balance" disabled=no \
dst-address-list=loopback in-interface=Local
add action=mark-connection chain=input comment=\
"Marca nova conexo de entrada wan1" connection-state=new disabled=no \
in-interface=pppoe-out1 new-connection-mark=wan1 passthrough=yes
add action=mark-connection chain=input comment=\
"Marca nova conexo de entrada wan2" connection-state=new disabled=no \
in-interface=pppoe-out2 new-connection-mark=wan2 passthrough=yes
add action=mark-connection chain=prerouting comment=\
"Marca conexo de entrada estabelecidas wan1" connection-state=established \
disabled=no in-interface=pppoe-out1 new-connection-mark=wan1 passthrough=\
yes
add action=mark-connection chain=prerouting comment=\
"Marca conexo de entrada estabelecidas wan2" connection-state=established \
disabled=no in-interface=pppoe-out2 new-connection-mark=wan2 passthrough=\
yes
add action=mark-connection chain=prerouting comment=\
"Marca conexo de entrada relacionadas wan1" connection-state=related \
disabled=no in-interface=pppoe-out1 new-connection-mark=wan1 passthrough=\
yes
add action=mark-connection chain=prerouting comment=\
"Marca conexo de entrada relacionadas wan2" connection-state=related \
disabled=no in-interface=pppoe-out2 new-connection-mark=wan2 passthrough=\
yes
add action=mark-routing chain=output comment=\
"Marca nova rota de entrada wan1" connection-mark=wan1 disabled=no \
new-routing-mark=static-wan1 passthrough=yes
add action=mark-routing chain=output comment=\
"Marca nova rota de entrada wan2" connection-mark=wan2 disabled=no \
new-routing-mark=static-wan2 passthrough=no
add action=mark-connection chain=prerouting comment="Marca trfego que no loca\
l com rand marca PCC (3 possibilidades) - opo 1" connection-state=new \
disabled=no dst-address-type=!local in-interface=Local \
new-connection-mark=wan1_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/0
add action=mark-connection chain=prerouting comment="Marca trfego que no loca\
l com rand marca PCC (3 possibilidades) - opo 2" connection-state=new \
disabled=no dst-address-type=!local in-interface=Local \
new-connection-mark=wan2_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/1
add action=mark-connection chain=prerouting comment="Marca trfego estabelecido\
\_que no local com rand marca PCC (3 possibilidades) - opo 1" \
connection-state=established disabled=no dst-address-type=!local \
in-interface=Local new-connection-mark=wan1_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/0
add action=mark-connection chain=prerouting comment="Marca trfego estabelecido\
\_que no local com rand marca PCC (3 possibilidades) - opo 2" \
connection-state=established disabled=no dst-address-type=!local \
in-interface=Local new-connection-mark=wan2_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/1
add action=mark-connection chain=prerouting comment="Marca trfego relacionado \
que no local com rand marca PCC (3 possibilidades) - opo 1" \
connection-state=related disabled=no dst-address-type=!local \
in-interface=Local new-connection-mark=wan1_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/0
add action=mark-connection chain=prerouting comment="Marca trfego relacionado \
que no local com rand marca PCC (3 possibilidades) - opo 2" \
connection-state=related disabled=no dst-address-type=!local \
in-interface=Local new-connection-mark=wan2_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/1
add action=mark-routing chain=prerouting comment=\
"Marca encaminhamento para marcar PCC - opo 1" connection-mark=\
wan1_pcc_conn disabled=no new-routing-mark=wan1 passthrough=yes
add action=mark-routing chain=prerouting comment=\
"Marca encaminhamento para marcar PCC - opo 2" connection-mark=\
wan2_pcc_conn disabled=no new-routing-mark=wan2 passthrough=yes





/ip route
add check-gateway=arp comment="Rota esttica - WAN1" disabled=no distance=1 \
dst-address=0.0.0.0/0 gateway=pppoe-out1 routing-mark=static-wan1 scope=\
30 target-scope=10
add check-gateway=arp comment="Rota esttica - WAN2" disabled=no distance=2 \
dst-address=0.0.0.0/0 gateway=pppoe-out2 routing-mark=static-wan2 scope=\
30 target-scope=10
add check-gateway=arp comment="WAN 1 - Distance 1" disabled=no distance=1 \
dst-address=0.0.0.0/0 gateway=pppoe-out1 routing-mark=wan1 scope=30 \
target-scope=10
add check-gateway=arp comment="WAN 1 - Distance 2" disabled=no distance=2 \
dst-address=0.0.0.0/0 gateway=pppoe-out2 routing-mark=wan1 scope=30 \
target-scope=10
add check-gateway=ping comment="" disabled=yes distance=1 dst-address=\
0.0.0.0/0 gateway=pppoe-out1 routing-mark=wan1 scope=30 target-scope=10
add check-gateway=arp comment="WAN 2 - Distance 1" disabled=no distance=1 \
dst-address=0.0.0.0/0 gateway=pppoe-out2 routing-mark=wan2 scope=30 \
target-scope=10
add check-gateway=arp comment="WAN 2 - Distance 3" disabled=no distance=2 \
dst-address=0.0.0.0/0 gateway=pppoe-out1 routing-mark=wan2 scope=30 \
target-scope=10
add check-gateway=ping comment="" disabled=yes distance=1 dst-address=\
0.0.0.0/0 gateway=pppoe-out2 routing-mark=wan2 scope=30 target-scope=10
add check-gateway=arp comment="Default Route - Distance 1" disabled=no \
distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out1 scope=30 \
target-scope=10
add check-gateway=arp comment="Default Route - Distance 3" disabled=no \
distance=2 dst-address=0.0.0.0/0 gateway=pppoe-out2 scope=30 \
target-scope=10
add comment="" disabled=yes distance=1 dst-address=0.0.0.0/0 gateway=Local \
scope=30 target-scope=10
add check-gateway=ping comment="" disabled=yes distance=1 dst-address=\
0.0.0.0/0 gateway=pppoe-out1 scope=30 target-scope=10
add check-gateway=ping comment="" disabled=yes distance=2 dst-address=\
0.0.0.0/0 gateway=pppoe-out2 scope=30 target-scope=10




esta correto minhas rotas e marcações , trabalho com 2 modens em brisge da mesma operadora , ate mais

é normal ele usar sempre um mais que outro.

OK valeu

são iguais os links mesmo up e down?

nao é certo um link ficar muito acima do outro não se forem de velocidades diferentes sim é normal pelo que vejo tem um erro não sei se vc quis assim


new-connection-mark=wan1_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/0
add action=mark-connection chain=prerouting comment="Marca trfego que no loca\
l com rand marca PCC (3 possibilidades) - opo 2" connection-state=new \
disabled=no dst-address-type=!local in-interface=Local \
new-connection-mark=wan2_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/1
add action=mark-connection chain=prerouting comment="Marca trfego estabelecido\
\_que no local com rand marca PCC (3 possibilidades) - opo 1" \
connection-state=established disabled=no dst-address-type=!local \
in-interface=Local new-connection-mark=wan1_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/0
add action=mark-connection chain=prerouting comment="Marca trfego estabelecido\
\_que no local com rand marca PCC (3 possibilidades) - opo 2" \
connection-state=established disabled=no dst-address-type=!local \
in-interface=Local new-connection-mark=wan2_pcc_conn passthrough=yes \
per-connection-classifier=both-addresses:2/1
add action=mark-connection chain=prerouting comment="Marca trfego relacionado \
que no local com rand marca PCC (3 possibilidades) - opo 1" \


se são 2 links para que 4 regras?
pode usar somente 2

to batendo cabeça com isso , que M , nao consigo deixar redondo .


Links iguais