+ Responder ao Tópico



  1. #13
    Moderador Avatar de Bruno
    Ingresso
    Nov 2002
    Localização
    Guarapuava-PR
    Posts
    3.943
    Posts de Blog
    1

    Padrão

    olha depois que tu salvar ele vai ir direto para a flash

  2. #14

    Padrão ainda nao foi

    Cara fiz do geito que vc falou ... configurei so o ip da Fastethernet pra agilizar dei write memory --->building .... depois desliguei o router e de novo ele aparece a tela


    Would you like to enter the initial configuration dialog?( yes/no )

    to achando q o boot dele ta indo pra outro lugar ....vo copiar oq ele ta fazendo e colocar ai



  3. #15

    Padrão ai vai

    ystem Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)
    TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
    Copyright (c) 2001 by cisco Systems, Inc.
    C1700 platform with 65536 Kbytes of main memory
    Allocating additional 5955395 bytes to IO Memory.
    PMem allocated: 57713293 bytes; IOMem allocated: 9395571 bytes


    If any of the above Memory Requirements are
    "UNKNOWN", you may be using an unsupported
    configuration or there is a software problem and
    system operation may be compromised.



    Allocating additional 5955395 bytes to IO Memory.
    Allocating additional 5955395 bytes to IO Memory.


    Restricted Rights Legend

    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.

    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 9513

    Cisco Internetwork Operating System Software
    IOS (tm) C1700 Software (C1700-SY7-M), Version 12.3(15b), RELEASE SOFTWARE (fc1)

    Copyright (c) 1986-2005 by cisco Systems, Inc.
    Compiled Thu 25-Aug-05 20:28 by ssearch
    Image text-base: 0x8000816C, data-base: 0x80E5340C

    cisco 1751 (MPC860P) processor (revision 0x600) with 56360K/9176K bytes of memor
    y.
    Processor board ID JAD06370DZR (3022442426), with hardware revision 0000
    MPC860P processor: part number 5, mask 2
    Bridging software.
    X.25 software, Version 3.0.0.
    1 FastEthernet/IEEE 802.3 interface(s)
    2 Serial(sync/async) network interface(s)
    32K bytes of non-volatile configuration memory.
    16384K bytes of processor board System flash (Read/Write)


    --- System Configuration Dialog ---

    Would you like to enter the initial configuration dialog? [yes/no]:

  4. #16

    Padrão

    Cara, verifica o config register esse router... pode ser isso.

    Se voce der um show startup-config e ve se as configs q vc fez estoa laá



  5. #17

    Padrão Certo Mestre

    Primeiramente ... queria agradecer a todos pela ajuda que estao me dando .

    Certo Mestre Misty.....apos dizer aquela msg de configuração inicial ( yes / no ) eu dizendo no ... e entrando no modo de configuração .... se eu der (show startup-config) aparece sim as configurações que eu tinha feito ( somente Ip da fastethernet - nao foi feito + nada so pra testar ) porem o router nao esta inicializando por ela ..... alguam coisa devo ter feito errado ....pq ele fica dando aquela msg segue abaixo STARTUP-CONFIG


    Using 580 out of 29688 bytes
    !
    version 12.3
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname Router
    !
    boot-start-marker
    boot system flash
    boot-end-marker
    !
    !
    mmi polling-interval 60
    no mmi auto-configure
    no mmi pvc
    mmi snmp-timeout 180
    no aaa new-model
    ip subnet-zero
    p cef
    !
    !
    !
    !
    interface FastEthernet0/0
    ip address 10.0.3.1 255.255.255.0
    speed auto
    !
    interface Serial0/0
    no ip address
    shutdown
    !
    interface Serial1/0
    no ip address
    shutdown
    !
    ip classless
    no ip http server
    line con 0
    line aux 0
    line vty 0 4

    Aguardo ....

  6. #18

    Padrão

    Bom, me deu um branco agora e eu nao tenho um cisco para mecher.. então faça o seguinte:

    entre no modo de configuracao global e bote la
    (config)# config-register 0x2102

    salve, e reboote o router