Com se configura PPPoe em moden cisco 877

Estou com um moden Cisco 877 que não consigo fazelo funcionar de manira alguma, quam uso ele em bridge, e tento discar meu ADSL (Oi Velox) Recebo a mensagem de login e senha incorretos, na verdade queria fazer-lo funcionar em modulo router se se ele funcionaar em bridge ja adiantaria minha vida bastante.

Vou deixar minhas configuracões logo a baixo pra que alguem com mas esperiência que eu possa dar uma olhada.

Desde de já grato!

Citação:

---

no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname ADSL_ROUTER
!
boot-start-marker
boot-end-marker
!
security authentication failure rate 3 log
security passwords min-length 6
logging buffered 51200 debugging
logging console critical
enable secret <Minha senha>
!
aaa new-model
!
!
aaa authentication login default local
aaa authorization exec default local
!
aaa session-id common
!
resource policy
!
no ip source-route
ip cef
!
!
!
!
ip tcp synwait-time 10
no ip bootp server
ip name-server 4.2.2.1
ip name-server 4.2.2.2
!
!
!
!
!
!
interface ATM0
no shutdown
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
no shutdown
no snmp trap link-status
pvc 0/33


encapsulation aal5snap ppp dialer ß ( desconfio que o erro esteja aqui mas não consigo mudar)
dialer pool-member 1
!
!
interface FastEthernet0
no shutdown
!
interface FastEthernet1
no shutdown
!
interface FastEthernet2
no shutdown
!
interface FastEthernet3
no shutdown
!
interface Vlan1
no shutdown
ip address 192.168.0.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip route-cache flow
ip tcp adjust-mss 1452
!
interface Dialer0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip inspect DEFAULT100 out
ip virtual-reassembly
encapsulation ppp
ip route-cache flow
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap callin
ppp chap hostname <[email protected]>
ppp chap password < DDD+meutelefone >
!
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 192.168.0.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
!
!
!
!
control-plane
!
banner login CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!
!
line con 0
no modem enable
transport output telnet
line aux 0
transport output telnet
line vty 0 4
transport input telnet
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
!
!
end

---

Estou postando uma das configurações que fiz e funcionou legal, ela tinha uma serie de config de VPNS o qual retirei e não fiz uma revisão, mas deve lhe servir.

Current configuration : 2320 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname xxxxxxxx
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
!
ip cef
vpdn enable
!
bba-group pppoe global
!
!
interface Ethernet0
description *** LAN INTERNA ***
ip address xxx.xxx.xxx.xxx 255.255.255.0
ip nat inside
ip virtual-reassembly
!
interface Ethernet1
description *** Rede WAN ***
no ip address
duplex auto
pppoe enable
pppoe-client dial-pool-number 1
!
interface FastEthernet1
duplex auto
speed auto
!
interface FastEthernet2
duplex auto
speed auto
!
interface FastEthernet3
duplex auto
speed auto
!
interface FastEthernet4
duplex auto
speed auto
!
interface Dialer1
description *** Conexao PPPoE ***
ip address negotiated
ip mtu 1492
ip nat outside
no ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username xxxxx password 0 xxxxx
!
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
no ip http secure-server
!
control-plane
!
line con 0
password xxxxxxxxx
login
no modem enable
line aux 0
line vty 0 4
password xxxxxxxxx
login
!
scheduler max-task-time 5000
end

interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
no shut
!
interface ATM0.1 point-to-point
description $ES_WAN$
no snmp trap link-status
pvc 0/33
pppoe-client dial-pool-number 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
description $FW_INSIDE$
ip address 10.75.20.45 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
no shut
!
interface Dialer0
description $FW_OUTSIDE$
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp pap sent-username [email protected] password 0 7112345678
!
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 10.75.20.0 0.0.0.255
dialer-list 1 protocol ip permit

Perdoem a ignorância, mas conde eu insiro essa configurações, estou apanhando muito para configurar um modem desses. Alguém teria a configuração dele para bridge?

Amigo você coloca esses parâmetro em telnet. Executar>telnet para abrir.
Então é só digitar isso se seu cisco tem as configurações de fabrica.
o 10.10.10.1
login: cisco
senha: cisco
Router> enable // entra modo privilegiado, caso exista senha, basta digitá-la
Pronto agora é só adicionar os parâmetros.