lilo "error 0x10"

eu uso linux e windows em uma mesma maquina, em dois HDs diferentes, o primario com linux e secundario com windows, porem na hora de iniciar, aperto para entrar no lilo, e da o seguinte erro....

error 0x10

então fica fazendo uma contagem de 5 segundos e não sai disso, se tento entrar no windows, a tela fica preta e não ocorre mais nada!

a distro é um slack 10, com kernel série 2.4(infelizmente não sei a release), também não sei a versão do lilo!

alguém tem uma solução?

valeu!

Gente, eu tenho este problema! Adicionando as opções "map" e "to" na parte do Windows ele aceita o boot! Alguém sabe me explicar que opções são estas?

Abaixo o que eu encontrei no google, mas não me ajudou muito não, se alguém puder ajudar... Em negrito está o erro 0x10

---------------------------------------------------------------------------
Disk error codes
- - - - - - - -


If the BIOS signals an error when LILO is trying to load a boot image,
the
respective error code is displayed. The following BIOS error codes are
known:


0x00 "Internal error". This code is generated by the sector read routine of the LILO boot loader whenever an internal inconsistency is detected. This might be caused by corrupt files. Try re-building the map file. Another possible cause for this error are attempts to access cylinders beyond 1024 while using the LINEAR option. See section "BIOS
restrictions" for more details and for how to solve the problem.
0x01 "Illegal command". This shouldn't happen, but if it does, it
may
indicate an attempt to access a disk which is not supported by the
BIOS. See also "Warning: BIOS drive 0x<number> may not be
accessible"
in section "Warnings".
0x02 "Address mark not found". This usually indicates a media
problem.
Try again several times.
0x03 "Write-protected disk". This should only occur on write
operations.
0x04 "Sector not found". This typically indicates a geometry
mismatch.
If you're booting a raw-written disk image, verify whether it was
created for disks with the same geometry as the one you're using. If
you're booting from a SCSI disk or a large IDE disk, you should
check,
whether LILO has obtained correct geometry data from the kernel or
whether the geometry definition corresponds to the real disk
geometry.
(See section "Disk geometry".) Removing COMPACT may help too. So may
adding LINEAR.
0x06 "Change line active". This should be a transient error. Try
booting a second time.
0x07 "Invalid initialization". The BIOS failed to properly
initialize
the disk controller. You should control the BIOS setup parameters. A
warm boot might help too.
0x08 "DMA overrun". This shouldn't happen. Try booting again.
0x09 "DMA attempt across 64k boundary". This shouldn't happen. Try
omitting the COMPACT option and report this problem to the author.
0x0C "Invalid media". This shouldn't happen and might be caused by
a
media error. Try booting again.
0x10 "CRC error". A media error has been detected. Try booting
several
times, running the map installer a second time (to put the map file
at
some other physical location or to write "good data" over the bad
spot), mapping out the bad sectors/tracks and, if all else fails,
replacing the media.
0x11 "ECC correction successful". A read error occurred, but was
corrected. LILO does not recognize this condition and aborts the
load
process anyway. A second load attempt should succeed.
0x20 "Controller error". This shouldn't happen.
0x40 "Seek failure". This might be a media problem. Try booting
again.
0x80 "Disk timeout". The disk or the drive isn't ready. Either the
media is bad or the disk isn't spinning. If you're booting from a
floppy, you might not have closed the drive door. Otherwise, trying
to
boot again might help.
0xBB "BIOS error". This shouldn't happen. Try booting again. If the
problem persists, removing the COMPACT option or adding/removing
LINEAR
might help.


If the error occurred during a write operation, the error code (two hex
digits) is prefixed with a "W". Although write errors don't affect the
boot
process, they might indicate a severe problem, because they usually
imply
that LILO has tried to write to an invalid location. If spurious write
errors occur on a system, it might be a good idea to configure LILO to
run
read-only (see section "Build-time configuration").


Generally, invalid geometry and attempts to use more than two disks
without
a very modern BIOS may yield misleading error codes. Please check
carefully
if /sbin/lilo doesn't emit any warnings. Then try using the LINEAR
option
(see section "Global options").
-----------------------------------------------------------------------------

Pelo que eu sei, geralmete o lilo dá pau quando ocorre erro na tabela de particionamento da MBR, por algum motivo o programa q fez o particionamento da unidade tá dando pau, aqui deu isso uma vez,foi só recriar as partićões com o CFDISK, e pronto, o lilo rodou tranquilo.....
claro que quando eu recriei as particões eu formatei tudo.....