gente tenho o seguinte quadro aki , um MK servidor e agora um MK AP
MK servidor ---->hub----->mk AP --->saindo por uma d-link 520
configuro a placa D-link 520 beleza da sinal tudo beleza conecto a ela , mais não consigo de maneira nenhuma navegar , vou colocar aki minhas configurações se alguem poder me ajudar vou ficar muito feliz pq não sei mais o q fazer
[admin@MikroTik] > /export
# feb/15/2007 11:38:54 by RouterOS 2.9.6
# software id = NCIJ-LXT
#
/ interface ethernet
set ether1 name="ether1" mtu=1500 mac-address=00:04:75:EE:E3:23 arp=enabled \
disable-running-check=yes auto-negotiation=yes full-duplex=yes \
cable-settings=default speed=100Mbps comment="" disabled=no
/ interface wireless
set wlan1 name="wlan1" mtu=1500 mac-address=00:19:5B:66:E2:55 arp=enabled \
disable-running-check=no radio-name="00195B66E255" mode=ap-bridge \
ssid="Repetidora Wireless" area="" frequency-mode=superchannel \
country=no_country_set antenna-gain=15 frequency=2412 band=2.4ghz-b \
scan-list=default rate-set=default \
supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps \
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps \
basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007 \
ack-timeout=dynamic tx-power-mode=default noise-floor-threshold=default \
periodic-calibration=default burst-time=disabled dfs-mode=none \
antenna-mode=ant-a wds-mode=disabled wds-default-bridge=none \
wds-ignore-ssid=no update-stats-interval=disabled \
default-authentication=yes default-forwarding=yes default-ap-tx-limit=0 \
default-client-tx-limit=0 hide-ssid=no security-profile=default \
disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both \
compression=no allow-sharedkey=no comment="" disabled=no
/ interface wireless nstreme
set wlan1 enable-nstreme=no enable-polling=yes framer-policy=none \
framer-limit=3200
/ interface wireless manual-tx-power-table
set wlan1 manual-tx-powers=1Mbps:17,2Mbps:17,5.5Mbps:17,11Mbps:17,6Mbps:17,9Mbp\
s:17,12Mbps:17,18Mbps:17,24Mbps:17,36Mbps:17,48Mbps:17,54Mbps:17
/ interface wireless security-profiles
set default name="default" mode=none wpa-unicast-ciphers="" \
wpa-group-ciphers="" pre-shared-key="" static-algo-0=none static-key-0="" \
static-algo-1=none static-key-1="" static-algo-2=none static-key-2="" \
static-algo-3=none static-key-3="" static-transmit-key=key-0 \
static-sta-private-algo=none static-sta-private-key="" \
radius-mac-authentication=no group-key-update=5m
/ interface wireless align
set frame-size=300 active-mode=yes receive-all=no \
audio-monitor=00:00:00:00:00:00 filter-mac=00:00:00:00:00:00 ssid-all=no \
frames-per-second=25 audio-min=-100 audio-max=-20
/ interface wireless snooper
set multiple-channels=yes channel-time=200ms receive-errors=no
/ interface wireless sniffer
set multiple-channels=no channel-time=200ms only-headers=no receive-errors=no \
memory-limit=10 file-name="" file-limit=10 streaming-enabled=no \
streaming-server=0.0.0.0 streaming-max-rate=0
/ interface bridge
add name="bridge1" mtu=1500 arp=enabled stp=no priority=32768 ageing-time=5m \
forward-delay=15s garbage-collection-interval=5s hello-time=2s \
max-message-age=20s comment="" disabled=no
/ interface bridge port
set ether1 bridge=none priority=128 path-cost=10
set wlan1 bridge=none priority=128 path-cost=10
/ interface l2tp-server server
set enabled=no max-mtu=1460 max-mru=1460 \
authentication=pap,chap,mschap1,mschap2 default-profile=default-encryption
/ interface pptp-server server
set enabled=no max-mtu=1460 max-mru=1460 authentication=mschap1,mschap2 \
keepalive-timeout=30 default-profile=default-encryption
/ ip telephony region
/ ip telephony gatekeeper
set gatekeeper=none remote-id="" remote-address=0.0.0.0
/ ip telephony aaa
set use-radius-accounting=no interim-update=0s
/ ip telephony codec
move G.711-uLaw-64k/sw
move G.711-ALaw-64k/sw
move G.729A-8k/sw
move G.729-8k/sw
move G.723.1-6.3k/sw
move GSM-06.10-13.2k/sw
move LPC-10-2.5k/sw
/ ip accounting
set enabled=no account-local-traffic=no threshold=256
/ ip accounting web-access
set accessible-via-web=no address=0.0.0.0/0
/ ip service
set telnet port=23 address=0.0.0.0/0 disabled=no
set ftp port=21 address=0.0.0.0/0 disabled=no
set www port=80 address=0.0.0.0/0 disabled=no
set ssh port=22 address=0.0.0.0/0 disabled=no
set www-ssl port=443 address=0.0.0.0/0 certificate=none disabled=yes
/ ip socks
set enabled=no port=1080 connection-idle-timeout=2m max-connections=200
/ ip arp
/ ip upnp
set enabled=no allow-disable-external-interface=yes show-dummy-rule=yes
/ ip traffic-flow
set enabled=no interfaces=all cache-entries=4k active-flow-timeout=30m \
inactive-flow-timeout=15s
/ ip dns
set primary-dns=192.168.0.1 secondary-dns=192.168.254.99 \
allow-remote-requests=yes cache-size=2048KiB cache-max-ttl=1w
/ ip address
add address=192.168.254.50/24 network=192.168.254.0 broadcast=192.168.254.255 \
interface=ether1 comment="" disabled=no
/ ip proxy
set enabled=no port=8080 parent-proxy=0.0.0.0:0 maximal-client-connecions=1000 \
maximal-server-connectons=1000
/ ip proxy access
add dst-port=23-25 action=deny comment="block telnet & spam e-mail relaying" \
disabled=no
/ ip neighbor discovery
set ether1 discover=yes
set wlan1 discover=yes
set bridge1 discover=yes
/ ip route
add dst-address=0.0.0.0/0 gateway=192.168.254.99 check-gateway=ping scope=255 \
target-scope=10 comment="" disabled=no
/ ip firewall nat
add chain=srcnat out-interface=ether1 src-address=192.168.254.0/24 \
action=masquerade comment="" disabled=no
add chain=dstnat src-address=192.168.254.0/24 protocol=tcp dst-port=80 \
action=redirect to-ports=3128 comment="" disabled=no