blz sou iniciante , como faz para copiar as regras
/ip firewall connection tracking
set enabled=yes generic-timeout=10m icmp-timeout=10s tcp-close-timeout=10s \
tcp-close-wait-timeout=10s tcp-established-timeout=1d \
tcp-fin-wait-timeout=10s tcp-last-ack-timeout=10s \
tcp-syn-received-timeout=5s tcp-syn-sent-timeout=5s tcp-syncookie=no \
tcp-time-wait-timeout=10s udp-stream-timeout=3m udp-timeout=10s
/ip firewall mangle
add action=accept chain=prerouting comment="FORA DO LOADBALACED" disabled=no \
dst-address-list=!loopback in-interface=!ether5
add action=mark-connection chain=input comment=\
"Make the packet leaves via same interface" connection-state=new \
disabled=no in-interface=!pppoe-out1 new-connection-mark=no-mark \
passthrough=yes
add action=mark-connection chain=input comment="" connection-state=new \
disabled=no in-interface=!pppoe-out2 new-connection-mark=no-mark \
passthrough=yes
add action=mark-routing chain=output comment="" connection-mark=!no-mark \
connection-state=new disabled=no new-routing-mark=main passthrough=no
add action=mark-routing chain=output comment="" connection-mark=!no-mark \
connection-state=new disabled=no new-routing-mark=main passthrough=no
add action=accept chain=prerouting comment=\
"Assigning the propper routing-mark" disabled=yes dst-address=\
!10.1.0.0/24 in-interface=!ether5
add action=accept chain=prerouting comment="" disabled=yes dst-address=\
!10.2.0.0/24 in-interface=!ether5
add action=mark-connection chain=prerouting comment="PCC Balance" disabled=no \
dst-address-type=local in-interface=!ether5 new-connection-mark=no-mark \
passthrough=no per-connection-classifier=both-addresses:2/0
add action=mark-connection chain=prerouting comment="" disabled=no \
dst-address-type=local in-interface=!ether5 new-connection-mark=no-mark \
passthrough=yes per-connection-classifier=!both-addresses:2/1
add action=mark-routing chain=prerouting comment="Marking all the packets" \
connection-mark=!no-mark disabled=no in-interface=!ether5 \
new-routing-mark=main passthrough=no
add action=mark-routing chain=prerouting comment="" connection-mark=!no-mark \
disabled=no in-interface=!ether5 new-routing-mark=main passthrough=no
/ip firewall nat
add action=masquerade chain=srcnat comment="Masquerade Interfaces" disabled=\
no out-interface=!pppoe-out1
add action=masquerade chain=srcnat comment="" disabled=no out-interface=\
!pppoe-out2
/ip firewall service-port
set ftp disabled=no ports=21
set tftp disabled=no ports=69
set irc disabled=no ports=6667
set h323 disabled=no
set sip disabled=no ports=5060,5061
set pptp disabled=no
/ip route
add check-gateway=ping comment="" disabled=no distance=1 dst-address=\
0.0.0.0/0 gateway=pppoe-out1 scope=30 target-scope=10
add check-gateway=ping comment="" disabled=no distance=1 dst-address=\
0.0.0.0/0 gateway=pppoe-out2 scope=30 target-scope=10
add check-gateway=ping comment="" disabled=no distance=1 dst-address=\
0.0.0.0/0 gateway=pppoe-out1 scope=30 target-scope=10
add check-gateway=ping comment="" disabled=no distance=2 dst-address=\
0.0.0.0/0 gateway=pppoe-out2 scope=30 target-scope=10
add comment="" disabled=yes distance=1 dst-address=0.0.0.0/0 gateway=ether5 \
scope=30 target-scope=10
Cara obrigado mesmo valeu aii funciono balaaaaaaa
fiz igual ao falado acima pelo nosso colega , mais noto um consumo muito maior em um dos links , nao teria como distribuir mais as conexoes , uma coisa que me deixa encomodado é que os looks saem so por 1 dos links certo , e teria como dividilos