Página 1 de 3 123 ÚltimoÚltimo
+ Responder ao Tópico



  1. #1
    Pessoal,

    to com um problema. Aqui em casa nao consigo conectar meu CABLE MODEM da Ajato na Inet (SO -> RH9) de jeito nenhum...sempre vem a msg TERMINATED...

    Bem, ja fiz de tudo, entao, iniciei novamente em modo DEBUG e lhes mostro o log gerado. Qualquer luz, agradeco de coracao.

    Pelas ultimas linhas do log parece que estah havendo um erro de comunicacao, ele tah enviando pacotes a um destino invalido (DestAddr ff:ff:ff:ff:ff:ff), e como obviamente nao ha retorno, dah o problema. Quanto a parte fisica, eu estou nesse momento no Windows, eh a mesma maquina, e tah tudo funcionando aqui 8-(...bem lah vai...

    Realmente nao sei como resolver isso... e me desculpem por esta CARTA...

    ======= INICIO DO LOG =========
    ---------------------------------------------
    * The following section contains information about your system
    Fri Oct 17 17:08:43 BRST 2003
    Output of uname -a
    Linux home 2.4.20-Home0810200303 #14 Wed Oct 8 18:31:51 BRT 2003 i686
    athlon i386 GNU/Linux
    ---------------------------------------------
    * The following section contains information about your network
    * interfaces. The one you chose for PPPoE should contain the words:
    * ´UP´ and ´RUNNING´. If it does not, you probably have an Ethernet
    * driver problem.
    Output of ifconfig -a
    eth0 Link encap:Ethernet HWaddr MI:NH:A_<IMG SRC="images/forum/icons/icon_razz.gif">L:AC:A0
    BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:100
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    Interrupt:11 Base address:0x2f00

    eth1 Link encap:Ethernet HWaddr MI:NH:A_<IMG SRC="images/forum/icons/icon_razz.gif">L:AC:A1
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:100
    RX bytes:0 (0.0 b) TX bytes:96 (96.0 b)
    Interrupt:5 Base address:0x220

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    ---------------------------------------------
    * The following section contains information about kernel modules
    * If the module for your Ethernet card is &acute;tulip&acute;, you might
    * want to look for an updated version at http://www.scyld.com
    Output of lsmod
    Module Size Used by Not tainted
    ppp_synctty 7744 0 (unused)
    ppp_async 9344 0
    ppp_generic 20892 0 [ppp_synctty ppp_async]
    slhc 6660 0 [ppp_generic]
    autofs 12948 0 (autoclean) (unused)
    3c509 13268 1
    8139too 18440 0 (unused)
    mii 3960 0 [8139too]
    nls_iso8859-1 3484 1 (autoclean)
    ntfs 58304 1 (autoclean)
    keybdev 2912 0 (unused)
    mousedev 5428 0 (unused)
    hid 15912 0 (unused)
    input 5824 0 [keybdev mousedev hid]
    usb-uhci 25868 0 (unused)
    usbcore 76896 1 [hid usb-uhci]
    ext3 69984 2
    jbd 51220 2 [ext3]
    ---------------------------------------------
    * The following section lists your routing table.
    * If you have an entry which starts with &acute;0.0.0.0&acute;, you probably
    * have defined a default route and gateway, and pppd will
    * not create a default route using your ISP. Try getting
    * rid of this route.
    Output of netstat -n -r
    Kernel IP routing table
    Destination Gateway Genmask Flags MSS Window
    irtt Iface
    169.254.0.0 0.0.0.0 255.255.0.0 U 0
    0 0 lo
    127.0.0.0 0.0.0.0 255.0.0.0 U 0
    0 0 lo
    ---------------------------------------------
    Contents of /etc/resolv.conf
    * The following section lists DNS setup.
    * If you can browse by IP address, but not name, suspect
    * a DNS problem.
    nameserver xxx.xxx.xxx.x (jah conferi, estao certos...)
    nameserver xxx.xxx.xxx.x
    ---------------------------------------------
    * The following section lists /etc/ppp/options.
    * You should have NOTHING in that file.
    Contents of /etc/ppp/options
    ---------------------------------------------
    * The following section identifies your Ethernet interface
    * and user name. Some ISP&acute;s need &acute;username&acute;; others
    * need &acute;username@i...&acute;. Try both
    ETH=eth1; USER=meu_user@a... (tb estah correto...e a senha tb)
    ---------------------------------------------
    * The following section shows the pppd command we will invoke
    pppd invocation
    /usr/bin/setsid /usr/sbin/pppd pty &acute;/usr/sbin/pppoe -
    p /var/run/pppoe.conf-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 &acute;
    noipdefault noauth default-asyncmap defaultroute hide-password
    nodetach mtu 1492 mru 1492 noaccomp noccp nobsdcomp nodeflate
    nopcomp novj novjccomp user meu_user@a... lcp-echo-interval 20
    lcp-echo-failure 3 debug
    ---------------------------------------------
    using channel 2
    Using interface ppp0
    Connect: ppp0 <--> /dev/pts/0
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    sent [LCP ConfReq id=0x1 <mru 1492> <magic 0x5ae1a383>]
    LCP: timeout sending Config-Requests
    Connection terminated.
    Waiting for 1 child processes...
    script /usr/sbin/pppoe -p /var/run/pppoe.conf-adsl.pid.pppoe -I
    eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-945/pppoe-debug.txt-0,
    pid 1003
    pppoe: Timeout waiting for PADO packets
    Script /usr/sbin/pppoe -p /var/run/pppoe.conf-adsl.pid.pppoe -I eth1 -
    T 80 -U -m 1412 -D /tmp/pppoe-debug-945/pppoe-debug.txt-0
    finished (pid 1003), status = 0x1
    ---------------------------------------------
    * The following section is an extract from your log.
    * Look for error messages from pppd, such as
    * a lack of kernel support for PPP, authentication failure
    * etc.
    Extract from /var/log/messages
    Oct 17 16:51:36 home pppd[804]: pppd 2.4.1 started by root, uid 0
    Oct 17 16:51:36 home pppd[804]: Using interface ppp0
    Oct 17 16:51:36 home pppd[804]: Connect: ppp0 <--> /dev/pts/0
    Oct 17 16:51:36 home /etc/hotplug/net.agent: assuming ppp0 is already
    up
    Oct 17 16:52:07 home pppd[804]: LCP: timeout sending Config-Requests
    Oct 17 16:52:07 home pppd[804]: Connection terminated.
    Oct 17 16:52:11 home pppoe[805]: Timeout waiting for PADO packets
    Oct 17 16:52:11 home pppd[804]: Exit.
    Oct 17 17:07:50 home pppd[758]: pppd 2.4.1 started by root, uid 0
    Oct 17 17:07:50 home pppd[758]: Using interface ppp0
    Oct 17 17:07:50 home pppd[758]: Connect: ppp0 <--> /dev/pts/0
    Oct 17 17:08:22 home pppd[758]: LCP: timeout sending Config-Requests
    Oct 17 17:08:22 home pppd[758]: Connection terminated.
    Oct 17 17:08:26 home pppoe[759]: Timeout waiting for PADO packets
    Oct 17 17:08:26 home pppd[758]: Exit.
    Oct 17 17:08:43 home pppd[1002]: pppd 2.4.1 started by root, uid 0
    Oct 17 17:08:43 home pppd[1002]: Using interface ppp0
    Oct 17 17:08:43 home pppd[1002]: Connect: ppp0 <--> /dev/pts/0
    Oct 17 17:09:14 home pppd[1002]: LCP: timeout sending Config-Requests
    Oct 17 17:09:14 home pppd[1002]: Connection terminated.
    Oct 17 17:09:18 home pppoe[1003]: Timeout waiting for PADO packets
    Oct 17 17:09:18 home pppd[1002]: Exit.
    Fri Oct 17 17:09:19 BRST 2003
    ---------------------------------------------
    * The following section is a dump of the packets
    * sent and received by rp-pppoe. If you don&acute;t see
    * any output, it&acute;s an Ethernet driver problem. If you only
    * see three PADI packets and nothing else, check your cables
    * and modem. Make sure the modem lights flash when you try
    * to connect. Check that your Ethernet card is in
    * half-duplex, 10Mb/s mode. If all else fails,
    * try using pppoe-sniff.
    rp-pppoe debugging dump
    rp-pppoe-3.5
    17:08:43.610 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12
    SourceAddr MI:NH:A_<IMG SRC="images/forum/icons/icon_razz.gif">L:AC:A1 DestAddr ff:ff:ff:ff:ff:ff
    01 01 00 00 01 03 00 04 eb 03 00 00 ............

    17:08:48.607 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12
    SourceAddr MI:NH:A_<IMG SRC="images/forum/icons/icon_razz.gif">L:AC:A1 DestAddr ff:ff:ff:ff:ff:ff
    01 01 00 00 01 03 00 04 eb 03 00 00 ............

    17:08:58.607 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12
    SourceAddr MI:NH:A_<IMG SRC="images/forum/icons/icon_razz.gif">L:AC:A1 DestAddr ff:ff:ff:ff:ff:ff
    01 01 00 00 01 03 00 04 eb 03 00 00 ............
    ======= FIM DO LOG =========


    De novo, agradeco qualquer ajuda!
    []s
    Adriano!

  2. #2
    beastie


    posta o teu pppoe.conf ai, blz?



  3. #3
    OK, como pedido...to postando o pppoe.conf e meu ifcfg-eth1 tb...

    ======INICIO DE PPPOE.CONF========
    #***************************************************
    #
    # pppoe.conf
    #
    # Configuration file for rp-pppoe. Edit as appropriate and install in
    # /etc/ppp/pppoe.conf
    #
    # NOTE: This file is used by the adsl-start, adsl-stop, adsl-connect and
    # adsl-status shell scripts. It is *not* used in any way by the
    # "pppoe" executable.
    #
    # Copyright (C) 2000 Roaring Penguin Software Inc.
    #
    # This file may be distributed under the terms of the GNU General
    # Public License.
    #
    # LIC: GPL
    # $Id: pppoe.conf,v 1.10 2002/04/09 17:28:38 dfs Exp $
    #******************************************************

    # When you configure a variable, DO NOT leave spaces around the "=" sign.

    # Ethernet card connected to ADSL modem
    ETH=&acute;eth1&acute;

    # ADSL user name. You may have to supply "@provider.com" Sympatico
    # users in Canada do need to include "@sympatico.ca"
    # Sympatico uses PAP authentication. Make sure /etc/ppp/pap-secrets
    # contains the right username/password combination.
    # For Magma, use xxyyzz@magma.ca
    USER=&acute;meu_user@ajato.com.br&acute;

    # Bring link up on demand? Default is to leave link up all the time.
    # If you want the link to come up on demand, set DEMAND to a number indicating
    # the idle time after which the link is brought down.
    DEMAND=no
    #DEMAND=300

    # DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2;
    # NOCHANGE=do not adjust.
    DNSTYPE=SPECIFY

    # Obtain DNS server addresses from the peer (recent versions of pppd only)
    # In old config files, this used to be called USEPEERDNS. Changed to
    # PEERDNS for better Red Hat compatibility
    PEERDNS=no

    DNS1=xxx.xxx.xxx.x
    DNS2=xxx.xxx.xxx.x

    # Make the PPPoE connection your default route. Set to
    # DEFAULTROUTE=no if you don&acute;t want this.
    DEFAULTROUTE=yes

    ### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU&acute;RE AN EXPERT

    # How long adsl-start waits for a new PPP interface to appear before
    # concluding something went wrong. If you use 0, then adsl-start
    # exits immediately with a successful status and does not wait for the
    # link to come up. Time is in seconds.
    #
    # WARNING WARNING WARNING:
    #
    # If you are using rp-pppoe on a physically-inaccessible host, set
    # CONNECT_TIMEOUT to 0. This makes SURE that the machine keeps trying
    # to connect forever after adsl-start is called. Otherwise, it will
    # give out after CONNECT_TIMEOUT seconds and will not attempt to
    # connect again, making it impossible to reach.
    CONNECT_TIMEOUT=30

    # How often in seconds adsl-start polls to check if link is up
    CONNECT_POLL=2

    # Specific desired AC Name
    ACNAME=

    # Specific desired service name
    SERVICENAME=

    # Character to echo at each poll. Use PING="" if you don&acute;t want
    # anything echoed
    PING="."

    # File where the adsl-connect script writes its process-ID.
    # Three files are actually used:
    # $PIDFILE contains PID of adsl-connect script
    # $PIDFILE.pppoe contains PID of pppoe process
    # $PIDFILE.pppd contains PID of pppd process
    CF_BASE=`basename $CONFIG`
    PIDFILE="/var/run/$CF_BASE-adsl.pid"

    # Do you want to use synchronous PPP? "yes" or "no". "yes" is much
    # easier on CPU usage, but may not work for you. It is safer to use
    # "no", but you may want to experiment with "yes". "yes" is generally
    # safe on Linux machines with the n_hdlc line discipline; unsafe on others.
    SYNCHRONOUS=no

    # Do you want to clamp the MSS? Here&acute;s how to decide:
    # - If you have only a SINGLE computer connected to the ADSL modem, choose
    # "no".
    # - If you have a computer acting as a gateway for a LAN, choose "1412".
    # The setting of 1412 is safe for either setup, but uses slightly more
    # CPU power.
    CLAMPMSS=1412
    #CLAMPMSS=no

    # LCP echo interval and failure count.
    LCP_INTERVAL=20
    LCP_FAILURE=3

    # PPPOE_TIMEOUT should be about 4*LCP_INTERVAL
    PPPOE_TIMEOUT=80

    # Firewalling: One of NONE, STANDALONE or MASQUERADE
    FIREWALL=NONE

    # Linux kernel-mode plugin for pppd. If you want to try the kernel-mode
    # plugin, use LINUX_PLUGIN=/etc/ppp/plugins/rp-pppoe.so
    LINUX_PLUGIN=

    # Any extra arguments to pass to pppoe. Normally, use a blank string
    # like this:
    PPPOE_EXTRA=""

    # Rumour has it that "Citizen&acute;s Communications" with a 3Com
    # HomeConnect ADSL Modem DualLink requires these extra options:
    # PPPOE_EXTRA="-f 3c12:3c13 -S ISP"

    # Any extra arguments to pass to pppd. Normally, use a blank string
    # like this:
    PPPD_EXTRA=""


    ########## DON&acute;T CHANGE BELOW UNLESS YOU KNOW WHAT YOU ARE DOING
    # If you wish to COMPLETELY overrride the pppd invocation:
    # Example:
    # OVERRIDE_PPPD_COMMAND="pppd call dsl"

    # If you want adsl-connect to exit when connection drops:
    # RETRY_ON_FAILURE=no

    ======FIM DE PPPOE.CONF========

    ======INICIO DE IFCFG-ETH1========
    DEVICE=eth1
    BOOTPROTO=dhcp
    ONBOOT=no
    NAME=3Com
    ======FIM DE IFCFG-ETH1========

    ...No RH9 ele inicializa a rede se o arquivo /etc/sysconfig/network for setado para yes. Ele inicializa as placas:

    ======INICIO DE NETWORK========
    NETWORKING=yes
    HOSTNAME=Home
    ======FIM DE NETWORK========

    Bem, de novo, agradeço qualquer luz...tava la ateh agora tentando fazer funcionar...


    []s
    Adriano!

  4. Cara,
    1 Como é que está a configuração do ip da sua placa eth1?
    2) Por que você não setou o ip do seu dns?



  5. #5
    Na verdade, os MACs, username e os servidores DNS estao todos setados. O que fiz foi ocultar esses valores aqui por motivo de seguranca...

    Bem, ainda estou com o problema, tava navegando e vi um kra que resolveu isso usando o dhcpcd...baixei, instalei, configurei como o kra falou, &acute;but nothing...&acute;...continuo com o problema.

    Quem puder ajudar...eu tb to atras e resolvendo isso, posto aqui!


    []s
    Adriano!






Tópicos Similares

  1. pppoe no Slackware
    Por gar0t0 no fórum Servidores de Rede
    Respostas: 14
    Último Post: 07-10-2003, 15:18
  2. não consigo o pacote rp-pppoe
    Por no fórum Servidores de Rede
    Respostas: 1
    Último Post: 27-11-2002, 17:59
  3. Autenticação PPPOE
    Por no fórum Servidores de Rede
    Respostas: 1
    Último Post: 14-11-2002, 14:38
  4. ADSL SPEEDY HOME (PPPOE) NO RED HAD 7.3
    Por no fórum Servidores de Rede
    Respostas: 3
    Último Post: 15-09-2002, 18:58
  5. Sobre PPPoE
    Por MarcelScan no fórum Servidores de Rede
    Respostas: 2
    Último Post: 06-04-2002, 20:15

Visite: BR-Linux ·  VivaOLinux ·  Dicas-L