SCSI Error - USB..mass storage

[JiGaBo0-forgotpasswd]

uso debian sarge(Testig)
kernel: 2.6.8-1-386

ao tentar montar o pendrive q comprei..

# mount /dev/sda1 /mnt/pendrive/
mount: /dev/sda1 is not a valid block device
# mount -t vfat /dev/sda1 /mnt/pendrive/
mount: /dev/sda1 is not a valid block device
#

dei uma verificada...... descobri isto:
alguem pode dar uma ajuda ??

usb 3-6: New high speed USB device using address 7
scsi3 : SCSI emulation for USB Mass Storage device
vendor: USB 2.0 model: Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 2048000 512-byte hdwr sectors (1049)MB
sda: assuming Write Enable
sda: assuming drive cache: write through
SCSI error: host 3 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
/dev/scsi/host3/bus0/target0/lun0: p1
SCSI error: host 3 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0

dando mais uma olhada verifiquei que minha usb tah trabalhando a 1.0.. meu pen drive.. eh USB 2.0 conforme visto em cima!.... eu li no manual da placa mae, e minha USB eh 2.0..... tah trabalhando a 1.0 nao sei pq... ae fika a pergunta.. como aumentar o speed dela...pra USB 2.0 ???????
blackforc:/home/daniel# dmesg
S
Security Scaffold v1.0.0 initialized
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
Uncovering SIS963 that hid as a SIS503 (compatible=0)
Enabling SiS 96x SMBus.
Linux Plug and Play Support v0.97 (c) Adam Belay
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4296 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdcMA, hddMA
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
hdc: HL-DT-ST RW/DVD GCC-4521B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
VFS: Can't find ext3 filesystem on dev hda3.
VFS: Can't find ext2 filesystem on dev hda3.
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0 Controller
ohci_hcd 0000:00:03.0: irq 11, pci mem d08f8000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:03.1 -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
ohci_hcd 0000:00:03.1: irq 5, pci mem d08fe000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb 2-2: new low speed USB device using address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:03.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ts: Compaq touchscreen protocol output
mice: PS/2 mouse device common for all mice
input: PC Speaker
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
inserting floppy driver for 2.6.8-1-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected SiS 746 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xd0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 10 (level, low) -> IRQ 10
intel8x0_measure_ac97_clock: measured 49668 usecs
intel8x0: clocking to 48000
ACPI: PCI interrupt 0000:00:03.2[D] -> GSI 12 (level, low) -> IRQ 12
ehci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 0000:00:03.2: irq 12, pci mem d0b43000
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:03.2
ehci_hcd 0000:00:03.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
usb 2-2: USB disconnect, address 2
ohci_hcd 0000:00:03.1: wakeup
usb 2-2: new low speed USB device using address 3
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:03.1-2
NET: Registered protocol family 17
eth0: Media Link On 100mbps full-duplex
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2047 buckets, 16376 max) - 296 bytes per conntrack
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02ca840(lo)
IPv6 over IPv4 tunneling driver
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
eth1: no IPv6 routers present
eth0: no IPv6 routers present
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
usb 3-6: new high speed USB device using address 3
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: USB 2.0 Model: Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
USB Mass Storage device found at 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
/dev/scsi/host0/bus0/target0/lun0: p1
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
usb 3-6: USB disconnect, address 3
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
eth1: no IPv6 routers present
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
eth1: no IPv6 routers present
eth1: no IPv6 routers present
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
usb 3-6: new high speed USB device using address 4
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: USB 2.0 Model: Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI error: host 1 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
/dev/scsi/host1/bus0/target0/lun0: p1
SCSI error: host 1 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
USB Mass Storage device found at 4
usb 3-6: USB disconnect, address 4
ohci_hcd 0000:00:03.0: wakeup
usb 1-3: new full speed USB device using address 2
usb 1-3: device not accepting address 2, error -110
usb 1-3: new full speed USB device using address 3
usb 1-3: device not accepting address 3, error -110
usb 3-6: new high speed USB device using address 6
scsi2 : SCSI emulation for USB Mass Storage devices
Vendor: USB 2.0 Model: Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI error: host 2 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
/dev/scsi/host2/bus0/target0/lun0: p1
SCSI error: host 2 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0
USB Mass Storage device found at 6
lp0: using parport0 (interrupt-driven).
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
usb 3-6: USB disconnect, address 6
usb 3-6: new high speed USB device using address 7
scsi3 : SCSI emulation for USB Mass Storage devices
Vendor: USB 2.0 Model: Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI error: host 3 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
/dev/scsi/host3/bus0/target0/lun0: p1
SCSI error: host 3 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0
USB Mass Storage device found at 7
usb 3-6: USB disconnect, address 7
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
eth1: no IPv6 routers present
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
usb 2-3: new full speed USB device using address 4
usb 2-3: device not accepting address 4, error -110
usb 2-3: new full speed USB device using address 5
usb 2-3: device not accepting address 5, error -110
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.





agradeco desde jah...
valews...

[nett]

Eu sei qué é básico, mas voce, já viu no setup ?